diff options
Diffstat (limited to 'benchmarks/dcn5.dat')
| -rw-r--r-- | benchmarks/dcn5.dat | 257 |
1 files changed, 257 insertions, 0 deletions
diff --git a/benchmarks/dcn5.dat b/benchmarks/dcn5.dat new file mode 100644 index 0000000..717b631 --- /dev/null +++ b/benchmarks/dcn5.dat @@ -0,0 +1,257 @@ +BEGIN NEW DATA CASE
+C BENCHMARK DCNEW-5
+C Derive Marti representation of 400-kV overhead Portuguese line as used
+C in subsequent simulation of DCNEW-7. From J. Allen Lima of EDP, 1981.
+C Discontinuity of April, 1992: the default conductance to ground was made
+C smaller, which changes the answers. To reproduce the previous answers
+C (we do not want to change these, for historical reasons), we have replaced
+C the previously-blank columns 33-40 of the Marti fitting card by 0.48D-7.
+C If erased, the smaller current default value of 0.32D-8 would be used.
+C 11 December 2001, add 2 definitions of STARTUP parameters. While using
+C RUNTP DISK, we want to see vector screen plots of the fitting. Salford
+C EMTP uses NOCALC = -1 for this. As for the great DISLIN graphics of
+C Mingw32 ATP, these are unaffected; they do not use NOCALC.
+$DEPOSIT, D4FACT=2.0 { Hold plots on screen for 2 seconds in spite of STARTUP
+$DEPOSIT, NOCALC=-1 { We want screen graphics during DISK in spite of STARTUP
+C Note about preceding. It would have been more general to move this from
+C the first to the 2nd subcase. But operation then would be defective. It
+C is necessary to make the change to NOCALC before the first use. Also,
+C do not try to cancel the definition at the start of some later subcase.
+C This, too, will be defective for Salford EMTP. Value NOCALC = -1 must
+C apply to the entire disk file if it applies at all. Of course, the user
+C normally will make the change outside of data and within STARTUP. The
+C use here merely documents the use in data, and illustrates use for one
+C standard test case.
+JMARTI SETUP
+$ERASE
+C LINHA CEDILLO-ORIOL (EDP23.DAT)
+C EXEMPLO DE APLICACAO - ANEXO 2
+BRANCH CEDIL1ORIOL1CEDIL2ORIOL2CEDIL3ORIOL3
+LINE CONSTANTS
+ 10.231 0.0840 4 1.25 -39.4 70.97 32.25 15.8 0.0 2
+ 20.231 0.0840 4 1.25 0.0 70.97 32.25 15.8 0.0 2
+ 30.231 0.0840 4 1.25 39.4 70.97 32.25 15.8 0.0 2
+ 00.5 0.58 4 .575 -25.76 100.07 76.12
+ 00.5 0.58 4 .575 25.76 100.07 76.12
+BLANK card ending conductor cards of imbedded "LINE CONSTANTS" data case
+ 250.0 5000.0 1 39.77 1
+ 250.0 50.0 1 39.77 1
+ 250.0 .01 1 39.77 9 10 1
+BLANK card ending frequency cards of imbedded "LINE CONSTANTS" data case
+BLANK card ending "LINE CONSTANTS" data cases
+C 345678901234567890123456789012345678901234567890123456789012345678901234567890
+C LECT +1 -4
+ 1 .48D-7
+ .30 30 0 1 1 0 0
+ .30 30 0 1 1 0 0 .0
+$PUNCH
+C Punched cards of "JMARTI SETUP" that began at 11-Aug-87 13.48.31
+C -1CEDIL1ORIOL1 2. 0.00 -2 3
+C 13 0.41285804706219800000E+03
+C 0.117013827128701600E+04 0.109328155224148600E+05 0.565854842148188200E+04
+C 0.486728968691983400E+04 0.707738202163730700E+05 0.683747081419827600E+06
+C 0.353541780131411400E+07 0.158128637229056500E+08 0.342732557798577400E+08
+C 0.393504407219363000E+08 0.341282907181993800E+08 0.204464663801654300E+08
+C 0.576218378853537400E+08
+C 0.658089815842887500E+01 0.690898889439574300E+02 0.124258964382556600E+03
+C 0.223516853729638100E+03 0.270128036573363500E+04 0.269143242842107800E+05
+C 0.146979058765937700E+06 0.698197935976008100E+06 0.314038859911038900E+07
+C 0.746337177863556100E+07 0.266392944394791100E+08 0.155396621655433500E+08
+C 0.219748648076802900E+08
+C 14 0.22647930777147510000E-03
+C 0.331451503980230500E+00 0.957810893440665900E+00 0.110134713681638100E+02
+C 0.180908805160478500E+02 0.781367826984978700E+02 0.103291086579887900E+04
+C 0.425775964441755200E+04 0.731076147881571700E+04 0.645086114448789600E+05
+C -0.121580640576776300E+07 0.120529056645769800E+07 0.269226714026515400E+11
+C -0.538881685119132500E+11 0.269654304065261300E+11
+C 0.589872958561511400E+02 0.171405582109428700E+03 0.179182409973538700E+04
+C 0.268435133910598700E+04 0.325142423749699900E+04 0.131857420615934700E+05
+C 0.213446094244524200E+05 0.291840101919225200E+05 0.635302462418500200E+05
+C 0.520162387212404600E+06 0.520682549599617000E+06 0.144355307435927900E+06
+C 0.144499662743363700E+06 0.144644162406106900E+06
+C -2CEDIL2ORIOL2 2. 0.00 -2 3
+C 14 0.32434436644879670000E+03
+C 0.252272221491383900E+04 -0.783260653525317500E+03 0.843607760308153000E+03
+C 0.405537446805999600E+03 0.172880473437216700E+03 0.230195610382546000E+03
+C 0.660733376851304400E+02 0.356064973429300400E+04 0.360876600484696400E+05
+C 0.458067308721601900E+06 0.155426951919825100E+07 0.349466741634103300E+07
+C 0.831361356808634600E+07 0.267191748194155000E+08
+C 0.395606796435294500E+01 0.463636540679569400E+01 0.937357763832626400E+01
+C 0.153396557146477500E+02 0.203063670799592800E+02 0.331878663859569700E+02
+C 0.611409934802217200E+02 0.268325289733025000E+04 0.271015097222632500E+05
+C 0.344182439511496500E+06 0.117037498667061200E+07 0.264512776776344300E+07
+C 0.633446917806616700E+07 0.205787510722953700E+08
+C 13 0.21476948015004290000E-03
+C 0.129886637076557500E+02 0.884003674519057400E+02 0.565725100840623100E+03
+C 0.292315788164491400E+04 0.117634493299715700E+05 0.532876816095669600E+05
+C 0.389311630824632000E+06 0.168009410995213200E+07 -0.473619579064887500E+06
+C 0.469591802445442400E+06 0.116082359059264000E+12 -0.233025568883434800E+12
+C 0.116941075804808200E+12
+C 0.257364856264644300E+04 0.165926108688265800E+05 0.470409224941954100E+05
+C 0.986656254049737000E+05 0.163110687161601600E+06 0.273917039852386800E+06
+C 0.492292953769284000E+06 0.752972255828020600E+06 0.140712894268528100E+08
+C 0.140853607162796500E+08 0.122661653779630500E+07 0.122784315433410000E+07
+C 0.122907099748843300E+07
+C -3CEDIL3ORIOL3 2. 0.00 -2 3
+C 11 0.28528038941022320000E+03
+C 0.105748940794460900E+04 0.844409223042977800E+03 0.989216010327055800E+03
+C 0.195811001056642700E+03 0.654649799725072200E+02 0.207639338793363700E+03
+C 0.194266409628094900E+03 0.878586181627698400E+02 0.171400400143261400E+03
+C 0.585371148745679700E+04 0.290267832276061300E+06
+C 0.291079232024637700E+01 0.541078559821623500E+01 0.100447144771793100E+02
+C 0.147071822048762200E+02 0.182300039492140500E+02 0.316863800567847800E+02
+C 0.503710160254755600E+02 0.800538621073617100E+02 0.148612948128817500E+03
+C 0.452161584069224300E+04 0.224665949971083600E+06
+C 13 0.21343895805884290000E-03
+C 0.108554887622543600E+02 0.236929928387411900E+03 0.325918823811401900E+03
+C 0.115252813965977800E+03 0.302921999671820500E+04 0.837524968172409600E+05
+C 0.344224576617094500E+06 0.348234393920939100E+06 0.961491764497367900E+07
+C 0.646090509980150900E+10 -0.636446729379484800E+10 0.109996742832034700E+11
+C -0.111065069364993700E+11
+C 0.207273725615293600E+04 0.441443915140279000E+05 0.617690223349205100E+05
+C 0.216547308002615800E+05 0.140708626146584300E+06 0.111273186182077900E+07
+C 0.171705317383626400E+07 0.212273774822868700E+07 0.588027295979568100E+07
+C 0.121782848302581600E+08 0.121904631150884000E+08 0.100139997953964900E+08
+C 0.100240137951918800E+08
+C 0.58951122 -0.70710678 -0.41265641
+C 0.00000000 0.00000000 0.00000000
+C 0.55222554 0.00000000 0.81205257
+C 0.00000000 0.00000000 0.00000000
+C 0.58951122 0.70710678 -0.41265641
+C 0.00000000 0.00000000 0.00000000
+BLANK card ending "JMARTI SETUP" data cases
+BEGIN NEW DATA CASE
+C 2nd of 3 subcases serves to document correct use of the METRIC switch
+C of LINE CONSTANTS with JMARTI SETUP. There was a problem prior to
+C the end of October, 1992 (see paragraph ending the October newsletter).
+JMARTI SETUP
+BRANCH JDA LMA JDB LMB JDC LMC
+LINE CONSTANTS
+METRIC
+C LINE CONSTANTS DATA FOR JOHN DAY TO LOWER MONUMENTAL 500-KV LINE.
+ 1.3161 .1151 4 2.355 -6.5 22. 8.0
+C 2.3161 .1151 4 2.355 0.0 22. 8.0 --- disabled phase b
+C 3.3161 .1151 4 2.355 6.5 22. 8.0 --- disabled phase c
+C 0.5 4.189 4 0.914 -4.5 27.3 15.7 --- disabled ground wire
+ 0.5 4.189 4 0.914 4.5 27.3 15.7
+BLANK card ending conductor cards of imbedded "LINE CONSTANTS" data
+1500. 60. 1 108.7
+1500. .01 1 108.7 9 10
+BLANK card ending frequency cards of inbedded "LINE CONSTANTS" data
+BLANK card ending "LINE CONSTANTS" cases (back to "JMARTI SETUP")
+C Interesting observation about shunt conductance G on next data card. Here
+C we leave the associated data field blank, meaning that the default value
+C will be used. This requires a high-order (25-th order) polynomial. If
+C instead the erroneous English value .48D-7 of the first subcase were used,
+C the order would drop to 17. This is reasonable: with more leakage to
+C ground, the function changes less for frequencies. As the shunt G goes to
+C zero, the peak characteristic impedance approaches infinity.
+ 1 { Note use of default conductance G to ground }
+ .30 30 0 1 3 0 0
+ .30 30 0 1 3 0 0 .0
+$PUNCH
+C -1JDA LMA 2. 0.00 -2
+C 25 0.46006674819799320600E+03
+C -0.353674337503784091E+04 0.474463046762956129E+04 0.419877687068265857E+03
+C 0.120883875226538931E+04 0.137235831982550076E+04 0.176629375847576239E+04
+C 0.257098909773354399E+04 0.378828009143586360E+04 0.142803911584829507E+04
+C 0.265038440421150699E+05 0.580530772060140735E+05 0.290005305743382560E+05
+C 0.676240207790939604E+05 0.175744603974291211E+06 0.115920870054683113E+07
+C 0.568319643487089128E+07 0.919434012446274423E+07 0.170951429217248112E+08
+C 0.181624166300059595E+08 0.163578552517132629E+08 0.207902755237276070E+08
+C 0.163600109479811397E+08 0.305274580680562929E+08 0.282210275921647735E+08
+C 0.372990397194275335E+08
+C 0.277486902226732169E+00 0.268023805038167807E+00 0.415219939737164312E+00
+C 0.100965215215095117E+01 0.208586147663919608E+01 0.431742026198558549E+01
+C 0.938106002799715278E+01 0.216289195749565871E+02 0.471679540507255553E+02
+C 0.500972912994803551E+03 0.219672165983386822E+04 0.286843653676094892E+04
+C 0.114041795092961475E+05 0.297253629145985179E+05 0.991818044909751771E+05
+C 0.496349599086955830E+06 0.162826334212861327E+07 0.310812887668634393E+07
+C 0.660681407251698059E+07 0.123076413226896413E+08 0.154718145716374685E+08
+C 0.114181912129457910E+08 0.233626069519292787E+08 0.205401237474932187E+08
+C 0.289354784763300457E+08
+C 14 0.38047368960473913100E-03
+C 0.191762654465991029E-01 0.271854415897994640E+00 0.254872400058983795E+01
+C 0.960087067333501488E+01 0.353570965616266478E+02 0.689188689085494133E+02
+C 0.261362377354598903E+04 0.665059273530828341E+04 0.688588924417370727E+05
+C -0.304814667012787238E+07 0.302098170955132880E+07 0.392207514357697449E+11
+C -0.784954225679361268E+11 0.392746200573015366E+11
+C 0.335866402155424960E+01 0.477240584977659666E+02 0.433612099555737530E+03
+C 0.124259419864469488E+04 0.188504607192751701E+04 0.144958307619464109E+04
+C 0.172785300546916297E+05 0.280151013482649433E+05 0.736644708225197538E+05
+C 0.537133173259724048E+06 0.537670306432983838E+06 0.182411092478490581E+06
+C 0.182593503570969304E+06 0.182776097074540158E+06
+C 0.58951122
+C 0.00000000
+BLANK card ending JMARTI SETUP data cases
+BEGIN NEW DATA CASE
+C 3rd of 3 subcases serves to document correct use of the METRIC switch
+C of LINE CONSTANTS with JMARTI SETUP. This 3rd is identical to the 2nd
+C except this case is untransposed (see the extra "1" punch in column 70 of
+C frequency cards). Of course, with just 1 phase, answers are unchanged.
+JMARTI SETUP
+BRANCH JDA LMA JDB LMB JDC LMC
+LINE CONSTANTS
+METRIC
+C LINE CONSTANTS DATA FOR JOHN DAY TO LOWER MONUMENTAL 500-KV LINE.
+ 1.3161 .1151 4 2.355 -6.5 22. 8.0
+C 2.3161 .1151 4 2.355 0.0 22. 8.0 --- disabled phase b
+C 3.3161 .1151 4 2.355 6.5 22. 8.0 --- disabled phase c
+C 0.5 4.189 4 0.914 -4.5 27.3 15.7 --- disabled ground wire
+ 0.5 4.189 4 0.914 4.5 27.3 15.7
+BLANK card ending conductor cards of imbedded "LINE CONSTANTS" data
+C This 3rd case adds "1" punch in column 70 to indicate no transposition.
+C Also needed is an extra frequency card for the steady state (2nd of 3):
+1500. 60. 1 108.7 1
+1500. 60. 1 108.7 1
+1500. .01 1 108.7 9 10 1
+BLANK card ending frequency cards of inbedded "LINE CONSTANTS" data
+BLANK card ending "LINE CONSTANTS" cases (back to "JMARTI SETUP")
+C Interesting observation about shunt conductance G on next data card. Here
+C we leave the associated data field blank, meaning that the default value
+C will be used. This requires a high-order (25-th order) polynomial. If
+C instead the erroneous English value .48D-7 of the first subcase were used,
+C the order would drop to 17. This is reasonable: with more leakage to
+C ground, the function changes less for frequencies. As the shunt G goes to
+C zero, the peak characteristic impedance approaches infinity.
+ 1 { Note use of default conductance G to ground }
+ .30 30 0 1 3 0 0
+ .30 30 0 1 3 0 0 .0
+$PUNCH
+C -1JDA LMA 2. 0.00 -2
+C 25 0.46006674819799320600E+03
+C -0.353674337503784091E+04 0.474463046762956129E+04 0.419877687068265857E+03
+C 0.120883875226538931E+04 0.137235831982550076E+04 0.176629375847576239E+04
+C 0.257098909773354399E+04 0.378828009143586360E+04 0.142803911584829507E+04
+C 0.265038440421150699E+05 0.580530772060140735E+05 0.290005305743382560E+05
+C 0.676240207790939604E+05 0.175744603974291211E+06 0.115920870054683113E+07
+C 0.568319643487089128E+07 0.919434012446274423E+07 0.170951429217248112E+08
+C 0.181624166300059595E+08 0.163578552517132629E+08 0.207902755237276070E+08
+C 0.163600109479811397E+08 0.305274580680562929E+08 0.282210275921647735E+08
+C 0.372990397194275335E+08
+C 0.277486902226732169E+00 0.268023805038167807E+00 0.415219939737164312E+00
+C 0.100965215215095117E+01 0.208586147663919608E+01 0.431742026198558549E+01
+C 0.938106002799715278E+01 0.216289195749565871E+02 0.471679540507255553E+02
+C 0.500972912994803551E+03 0.219672165983386822E+04 0.286843653676094892E+04
+C 0.114041795092961475E+05 0.297253629145985179E+05 0.991818044909751771E+05
+C 0.496349599086955830E+06 0.162826334212861327E+07 0.310812887668634393E+07
+C 0.660681407251698059E+07 0.123076413226896413E+08 0.154718145716374685E+08
+C 0.114181912129457910E+08 0.233626069519292787E+08 0.205401237474932187E+08
+C 0.289354784763300457E+08
+C 14 0.38047368960473913100E-03
+C 0.191762654465991029E-01 0.271854415897994640E+00 0.254872400058983795E+01
+C 0.960087067333501488E+01 0.353570965616266478E+02 0.689188689085494133E+02
+C 0.261362377354598903E+04 0.665059273530828341E+04 0.688588924417370727E+05
+C -0.304814667012787238E+07 0.302098170955132880E+07 0.392207514357697449E+11
+C -0.784954225679361268E+11 0.392746200573015366E+11
+C 0.335866402155424960E+01 0.477240584977659666E+02 0.433612099555737530E+03
+C 0.124259419864469488E+04 0.188504607192751701E+04 0.144958307619464109E+04
+C 0.172785300546916297E+05 0.280151013482649433E+05 0.736644708225197538E+05
+C 0.537133173259724048E+06 0.537670306432983838E+06 0.182411092478490581E+06
+C 0.182593503570969304E+06 0.182776097074540158E+06
+C 0.58951122
+C 0.00000000
+BLANK card ending JMARTI SETUP data cases
+BEGIN NEW DATA CASE
+BLANK card
+
|