1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
BEGIN NEW DATA CASE
C BENCHMARK DC-32 --- modify
PRINTED NUMBER WIDTH, 12, 2, { Request maximum precision (for 8 output columns)
.000020 .01006
1 1 1 1 1 -1
5 5 10 10 50 50 500 1
C Three 2-winding saturable transformers having unity turns ratios are
C delta-connected on the source side, and grounded-Y on the rectifier
C side. The magnetizing branch is both nonlinear and lossy:
TRANSFORMER .01 .05TRANA 1.E5 1
.01 .05
.02 .06
.05 .07
.15 .08
9999
1GENA GENB .06 .01 115.
2SECA .06 .01 115.
TRANSFORMER TRANA TRANB 1
1GENB GENC
2SECB
TRANSFORMER TRANA TRANC 1
1GENC GENA
2SECC
C Small impedance branches are used (prior to "M34." generalized switch
C logic) to isolate switches from each other at "POLEA". R = 5 ohms.
C Although in theory such isolation is no longer required, do not try
C to remove these 9 resistors, since they provide necessary damping.
C Note that these resistors are not of negligible value:
CATH1 POLEA 5.0
CATH2 POLEA CATH1 POLEA
CATH3 POLEA CATH1 POLEA
C More small impedances used for switch isolation at node "POLEB", and
C also at the transformer secondary. Half the value of "POLEA" is used,
C for balance:
CATH4 SECC 2.5
CATH5 SECA CATH4 SECC
CATH6 SECB CATH4 SECC
AN4 POLEB CATH4 SECC
AN5 POLEB CATH4 SECC
AN6 POLEB CATH4 SECC
C 2-conductor distributed line connects "POLE" with "LOAD". Inductance
C parameters are 5.8 and 1.6 millihenries for the ground and sky modes,
C respectively. Length is five miles. Values are typical for 500 kV line:
-1POLEA LOADA 0.3 5.8 .012 5.0
-2POLEB LOADB .03 1.6 .019 5.0
C Large stray capacitance ties the dc side to ground:
POLEA 100.
POLEB POLEA
C Load on dc side is parallel 200 ohm R and 100 microfarad capacitance:
LOADA LOADB 200.
LOADA LOADB 100.
C One-ohm grounding resistance, for later fault (see DC-49 continuation).
LOADA FAULT 1.0
BLANK card ending all branch cards
C First switch is to be the fault switch (open here, and closed in DC-49):
FAULT 1.0 2.0
C Bridge circuit consisting of 6 uncontrolled valves (i.e., diodes). Those
C numbered 1, 2, and 3 feed "POLEA", making it positive with respect to
C ground. Diodes 4, 5, and 6 feed "POLEB", making it negative.
11SECB CATH1 13
11SECA CATH2 CLOSED 13
C The following card serves to name the switch following it. To see the
C results of this activity, interactively execute the "SWITCH" command of
C SPY, sending "EXTRA" for the alternative table. Another point: note
C the exclamation point, which is needed to hold lower case within A6 name
C (assuming KINSEN = 1 within STARTUP). No such control for valve six.
NAME: Valve3 ! { Request "NAME: " of cols. 3-8 precedes A6 valve name in 9-14
11SECC CATH3 13
11AN4 CATH4 CLOSED 13
11AN5 CATH5 13
NAME: Valve6 { Request "NAME: " of columns 3-8 precedes A6 valve name in 9-14
11AN6 CATH6 CLOSED 13
BLANK card terminating the last switch card
C Balanced 3-phase source of 400 Hz is connected to transformer delta side:
14GENA 93.897 400. -30. -1.
14GENB 93.897 400. -150. -1.
14GENC 93.897 400. 90. -1.
BLANK card ending all source cards
1 { Request for all node voltage outputs
BLANK card ending the last plot cards
BEGIN NEW DATA CASE
BLANK
|
