diff options
| author | Angelo Rossi <angelo.rossi.homelab@gmail.com> | 2023-06-21 12:04:16 +0000 |
|---|---|---|
| committer | Angelo Rossi <angelo.rossi.homelab@gmail.com> | 2023-06-21 12:04:16 +0000 |
| commit | b18347ffc9db9641e215995edea1c04c363b2bdf (patch) | |
| tree | f3908dc911399f1a21e17d950355ee56dc0919ee /benchmarks/dc61.dat | |
Initial commit.
Diffstat (limited to 'benchmarks/dc61.dat')
| -rw-r--r-- | benchmarks/dc61.dat | 203 |
1 files changed, 203 insertions, 0 deletions
diff --git a/benchmarks/dc61.dat b/benchmarks/dc61.dat new file mode 100644 index 0000000..981de3e --- /dev/null +++ b/benchmarks/dc61.dat @@ -0,0 +1,203 @@ +BEGIN NEW DATA CASE
+C BENCHMARK DC-61 (DC-64 of "M39." vintage)
+C South African simulation uses Semlyen line representation punched by DC-60
+C Compare this 2-exponential simulation with high-order Hauer one of DC-62.
+PRINTED NUMBER WIDTH, 12, 2, { Request maximum precision (for 9 output columns)
+POWER FREQUENCY, 50.,
+C PEAK VOLTAGE MONITOR { Original request is replaced by following 10 lines:
+C Columns 41-48 is taken to be a limit on node voltage. If this is exceeded,
+C ATP will halt. Note that keying "1" for MAXVLT in columns 33-40 is the same
+C as leaving the field blank. The default is "1", meaning a request for peak
+C node voltage. The alternate value "2" would be a request for peak branch
+C voltage. For HALTNV use, peak node voltage is required. As for the value
+C 1.E+300, this is close to the 32-bit Intel limit for floating-point math.
+C The limit is about 1.E+308. For more, see the 4th subcase of DC-37. WSM.
+C 3456789012345678901234567890123456789012345678
+C Ruler for following card: MAXVLT HALTNV { Format is: ( 32X, I8, E8.0 )
+PEAK VOLTAGE MONITOR 1 1.E300 { HALTNV use begins 9 Jan 2011
+ .000010 .020 50. 50.
+ 1 5 1 1 1 -1
+ 5 5 20 20 100 100 1000 1000
+ SA-3 BUSA-3 .1260.75
+ SA-4 BUSA-4 .1260.75
+ BUSA-1 2. .03
+ BUSA-2 2. .03
+ BUSA-3 FIL1 .1 47.12
+ FIL1 .1 90.76
+ FIL1 3. 74.24
+ FIL1 6.166.94 94.25
+ FIL1 12.314.16 11.06
+ FIL1 12.314.16 5.87
+ FIL2 .01 1021.
+ FIL2 .1 14.14
+ BUSA-4 FIL3 .1 47.12
+ FIL3 FIL4 .1 90.76
+ FIL3 FIL4 3. 74.24
+ FIL3 FIL4 6.166.94 94.25
+ FIL3 FIL4 12.314.16 11.06
+ FIL3 FIL4 12.314.16 5.87
+ FIL4 .01 1021.
+ FIL4 .01 14.14
+C &&&&&&&&&&&&&&&&& BEGIN LUNIT7 CARDS PUNCHED BY DC-63 (AUG. 1983) &&&&
+C L= 233.0MILES, RHO= 100.0, SS FREQ= 50.00, NSS=0, KFIT= 2, KPS=0, KYC= 1
+C METRIC
+C 1 .2 .273 4 1.7653 0. 39. 20.
+C 2 .2 .273 4 1.7653 30. 39. 20.
+C 3 .392 .0585 4 3.1750 2.3 27.5 8.5 50.8 45.
+C 4 .392 .0585 4 3.1750 32.3 27.5 8.5 50.8 45.
+C
+C 100. 5000. 1 375.
+C 100. 50. 1 375.
+C 100. 5. 1 375. 6 13
+C
+C -1BUSA-1BUSB-1 0.46613E-02 0.15134E-02 1 1 2 2 4
+C 0.12406072E+02 0.13647619E+03 0.26956084E-03 0.29653736E-02 0.50000000E+02
+C 0.00000E+00 0.27895E+04 0.89682E+00 0.00000E+00 0.28213E+03 0.10318E+00
+C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00
+C -1BUSA-2BUSB-2 0.75387E-02 0.12835E-02 2 2 2 2 4
+C 0.52771188E+00 0.55766835E+02 0.29991264E-04 0.31693770E-02 0.50000000E+02
+C 0.00000E+00 0.43289E+05 0.97097E+00 0.00000E+00 0.77845E+03 0.29034E-01
+C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00
+C -1BUSA-3BUSB-3 0.30274E-02 0.12573E-02 3 3 2 2 4
+C 0.13205030E+00 0.13401800E+03 0.12102672E-05 0.12283015E-02 0.50000000E+02
+C 0.00000E+00 0.15517E+06 0.81796E+00 0.00000E+00 0.62830E+04 0.18204E+00
+C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00
+C -1BUSA-4BUSB-4 0.27802E-02 0.12569E-02 4 4 2 2 4
+C 0.13237081E+00 0.14586679E+03 0.10231724E-05 0.11274909E-02 0.50000000E+02
+C 0.00000E+00 0.16860E+06 0.80035E+00 0.00000E+00 0.68259E+04 0.19965E+00
+C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00
+C 0.87120E+00 0.00000E+00-0.68291E+00 0.00000E+00 0.10000E+01 0.00000E+00
+C -0.41750E+00 0.00000E+00
+C 0.88389E+00 0.00000E+00 0.55491E+00 0.00000E+00 0.40829E+00 0.00000E+00
+C 0.10000E+01 0.00000E+00
+C 0.10000E+01 0.00000E+00-0.95444E+00 0.00000E+00-0.36612E+00 0.00000E+00
+C 0.81230E-01 0.00000E+00
+C 0.99538E+00 0.00000E+00 0.10000E+01 0.00000E+00-0.14418E+00 0.00000E+00
+C -0.28779E+00 0.00000E+00
+C 0.13754E+00 0.00000E+00-0.13506E+00 0.00000E+00 0.66301E+00 0.00000E+00
+C -0.32285E+00 0.00000E+00
+C 0.13718E+00 0.00000E+00 0.10517E+00 0.00000E+00 0.25843E+00 0.00000E+00
+C 0.72350E+00 0.00000E+00
+C 0.38034E+00 0.00000E+00-0.42191E+00 0.00000E+00-0.56809E+00 0.00000E+00
+C 0.13687E+00 0.00000E+00
+C 0.38061E+00 0.00000E+00 0.44851E+00 0.00000E+00-0.23947E+00 0.00000E+00
+C -0.49432E+00 0.00000E+00
+C &&&&&&&&&&&&&&&&& END LUNIT7 CARDS PUNCHED BY DC-63 &&&&&&&&
+C Preceding branch cards exist as non-comment data until 27 November 2000
+C when they are being replaced by more modern $INCLUDE use that makes
+C reference to cards punched by preceding DC-60:
+$INCLUDE, dc60a.pch, ! { Exclamation point to hold lower case is tolerated
+C In fact, it does nothing beginning 28 January 2001
+C At the same time, output of SEMLYEN SETUP is changing so [Tv] and [Ti]
+C use wide rather than preceding narrow format. But that newer data is
+C documented by output of DC-60, so need not be documented here.
+ TOWER 2.
+ BUSB-1 2. .03
+ BUSB-2 2. .03
+BLANK card ends all branch cards
+ BUSB-3TOWER .000995 1. 3
+BLANK cards ends all switch cards (here, just one, representing the fault)
+14SA-3 533000. 50. 0.0 -1.
+14SA-4 533000. 50. 180. -1.
+BLANK card ends source cards
+C Total network loss P-loss by summing injections = 1.227475331932E+07
+C 1st inject: SA-3 533000. 533000. 22.124947951506 1512.2473010922
+C 1st inject: 0.0 0.0 1512.0854428037 89.1617037
+C Last inject: SA-4 -533000. 533000. -23.93416394087 1518.1059386521
+C Last inject: .6527332453E-10 180.00000 -1517.917256232 -90.9033516
+C
+C Step Time BUSB-3 FIL2 TOWER FIL4 FIL3
+C TOWER
+C
+C BUSB-1 BUSA-2 BUSA-1 BUSA-4 BUSA-3
+C
+C 0 0.0 .101427E7 0.0 0.0 630.561229 3942.45992
+C -4.6091835 1.25763103 -3.3035273 -928794.53 927274.067
+C 1 .1E-4 .1014316E7 0.0 0.0 630.452909 3941.48093
+C -5.7370041 5.05435474 -4.8499099 -928814.11 927285.865
+ 1
+C Last step begins: 2000 .02 0.0 0.0 -4129.0322 3721.27842 -19338.153
+C Last step begins: 1060.61608 -481.80296 -509.22959 -915751.91 163602.568
+C Variable maxima : .1014355E7 0.0 5946.09635 40005.6129 123962.984
+C Variable maxima : 9268.51692 4258.29012 14305.2037 .1049562E7 927287.754
+C Times of maxima : .4E-4 0.0 .00723 .00952 .00505
+C Times of maxima : .00102 .00227 .00227 .01071 .2E-4
+ PRINTER PLOT
+ 2One section of 375 km.
+ 144 .6 0.0 7.0 BUSA-2 { Plot limits: (-0.647, 2.660)
+BLANK card ending all plot cards
+BEGIN NEW DATA CASE
+C 2nd of two subcases is the same as the preceding subcase except for one
+C change: the addition of "Derive [Ti] from [Tv]" immediately following
+C the Semlyen branch cards. The answers change a little. Even the limits
+C on the PRINTER PLOT are different. Date of addition: 11 December 2000.
+PRINTED NUMBER WIDTH, 12, 2, { Request maximum precision (for 9 output columns)
+POWER FREQUENCY, 50.,
+PEAK VOLTAGE MONITOR
+ .000010 .020 50. 50.
+ 1 5 1 1 1 -1
+ 5 5 20 20 100 100 1000 1000
+ SA-3 BUSA-3 .1260.75
+ SA-4 BUSA-4 .1260.75
+ BUSA-1 2. .03
+ BUSA-2 2. .03
+ BUSA-3 FIL1 .1 47.12
+ FIL1 .1 90.76
+ FIL1 3. 74.24
+ FIL1 6.166.94 94.25
+ FIL1 12.314.16 11.06
+ FIL1 12.314.16 5.87
+ FIL2 .01 1021.
+ FIL2 .1 14.14
+ BUSA-4 FIL3 .1 47.12
+ FIL3 FIL4 .1 90.76
+ FIL3 FIL4 3. 74.24
+ FIL3 FIL4 6.166.94 94.25
+ FIL3 FIL4 12.314.16 11.06
+ FIL3 FIL4 12.314.16 5.87
+ FIL4 .01 1021.
+ FIL4 .01 14.14
+$INCLUDE, dc60a.pch, { This is normal use, without any "!" (see subcase 2)
+Derive [Ti] from [Tv]
+ TOWER 2.
+ BUSB-1 2. .03
+ BUSB-2 2. .03
+BLANK card ends all branch cards
+ BUSB-3TOWER .000995 1. 3
+BLANK cards ends all switch cards (here, just one, representing the fault)
+14SA-3 533000. 50. 0.0 -1.
+14SA-4 533000. 50. 180. -1.
+BLANK card ends source cards
+C First 16 output variables are electric-network voltage differences (upper voltage minus lower voltage);
+C Next 1 output variables are branch currents (flowing from the upper node to the lower node);
+C Step Time BUSB-3 FIL2 TOWER FIL4 FIL3 FIL1 BUSB-3 BUSB-4 BUSB-2
+C TOWER
+C
+C BUSB-1 BUSA-2 BUSA-1 BUSA-4 BUSA-3 SA-3 SA-4 BUSB-3
+C TOWER
+C 0 0.0 .1009903E7 0.0 0.0 625.729384 3912.27257 -3290.8384 .1009903E7 -.100856E7 4.71090545
+C -4.7315816 1.50363292 -3.019058 -921677.25 923494.094 533000. -533000. 0.0
+C 1 .1E-4 .1009922E7 0.0 0.0 625.744428 3912.80237 -3291.3514 .1009922E7 -.100858E7 4.60636774
+C -4.6168248 2.20907585 -3.8531833 -921692.03 923507.81 532997.37 -532997.37 0.0
+C 2 .2E-4 .1009931E7 0.0 0.0 625.757165 3913.34087 -3291.8771 .1009931E7 -.100859E7 4.53586824
+C -4.5389958 2.951526 -4.73104 -921697.57 923512.279 532989.479 -532989.48 0.0
+ 1
+C 2000 .02 0.0 0.0 -4082.6074 3506.39056 -19843.969 33487.4084 -4082.6074 -994315.82 667.210123
+C 1019.1604 -477.59394 -495.04968 -910823.4 166982.83 533000. -533000. -2041.3037
+C
+C Overall simulation peak node voltage = 1.27438708E+06 occurred at bus "BUSB-4" at time [sec] = 9.42000000E-03
+C Extrema of output variables follow. Order and column positioning are the same as for the preceding time-step loop output.
+C Variable maxima : .1009931E7 0.0 5887.54564 39979.7091 122521.51 252007.816 .1009931E7 .1274387E7 5514.37962
+C 8875.03104 4249.33 13984.8846 .1041678E7 923512.279 533000. 533000. 2943.77282
+C Times of maxima : .2E-4 0.0 .00723 .00952 .00505 .00848 .2E-4 .00942 .00102
+C .00102 .00227 .00227 .01071 .2E-4 0.0 .01 .00723
+C Variable minima : 0.0 0.0 -7105.8822 -35654.766 -134500.78 -375615.01 -7105.8822 -.113035E7 -7267.3484
+C -11822.652 -1785.594 -1816.5115 -921697.57 -997977.99 -533000. -533000. -3552.9411
+C Times of minima : .00101 0.0 .01463 .01069 .00608 .00575 .01463 .00101 .00101
+C .00101 .01494 .0147 .2E-4 .0087 .01 0.0 .01463
+ PRINTER PLOT
+ 2One section of 375 km.
+ 144 .6 0.0 7.0 BUSA-2 { Plot limits: (-0.650, 2.600)
+BLANK card ending all plot cards
+BEGIN NEW DATA CASE
+BLANK
|