BEGIN NEW DATA CASE C BENCHMARK DC-61 (DC-64 of "M39." vintage) C South African simulation uses Semlyen line representation punched by DC-60 C Compare this 2-exponential simulation with high-order Hauer one of DC-62. PRINTED NUMBER WIDTH, 12, 2, { Request maximum precision (for 9 output columns) POWER FREQUENCY, 50., C PEAK VOLTAGE MONITOR { Original request is replaced by following 10 lines: C Columns 41-48 is taken to be a limit on node voltage. If this is exceeded, C ATP will halt. Note that keying "1" for MAXVLT in columns 33-40 is the same C as leaving the field blank. The default is "1", meaning a request for peak C node voltage. The alternate value "2" would be a request for peak branch C voltage. For HALTNV use, peak node voltage is required. As for the value C 1.E+300, this is close to the 32-bit Intel limit for floating-point math. C The limit is about 1.E+308. For more, see the 4th subcase of DC-37. WSM. C 3456789012345678901234567890123456789012345678 C Ruler for following card: MAXVLT HALTNV { Format is: ( 32X, I8, E8.0 ) PEAK VOLTAGE MONITOR 1 1.E300 { HALTNV use begins 9 Jan 2011 .000010 .020 50. 50. 1 5 1 1 1 -1 5 5 20 20 100 100 1000 1000 SA-3 BUSA-3 .1260.75 SA-4 BUSA-4 .1260.75 BUSA-1 2. .03 BUSA-2 2. .03 BUSA-3 FIL1 .1 47.12 FIL1 .1 90.76 FIL1 3. 74.24 FIL1 6.166.94 94.25 FIL1 12.314.16 11.06 FIL1 12.314.16 5.87 FIL2 .01 1021. FIL2 .1 14.14 BUSA-4 FIL3 .1 47.12 FIL3 FIL4 .1 90.76 FIL3 FIL4 3. 74.24 FIL3 FIL4 6.166.94 94.25 FIL3 FIL4 12.314.16 11.06 FIL3 FIL4 12.314.16 5.87 FIL4 .01 1021. FIL4 .01 14.14 C &&&&&&&&&&&&&&&&& BEGIN LUNIT7 CARDS PUNCHED BY DC-63 (AUG. 1983) &&&& C L= 233.0MILES, RHO= 100.0, SS FREQ= 50.00, NSS=0, KFIT= 2, KPS=0, KYC= 1 C METRIC C 1 .2 .273 4 1.7653 0. 39. 20. C 2 .2 .273 4 1.7653 30. 39. 20. C 3 .392 .0585 4 3.1750 2.3 27.5 8.5 50.8 45. C 4 .392 .0585 4 3.1750 32.3 27.5 8.5 50.8 45. C C 100. 5000. 1 375. C 100. 50. 1 375. C 100. 5. 1 375. 6 13 C C -1BUSA-1BUSB-1 0.46613E-02 0.15134E-02 1 1 2 2 4 C 0.12406072E+02 0.13647619E+03 0.26956084E-03 0.29653736E-02 0.50000000E+02 C 0.00000E+00 0.27895E+04 0.89682E+00 0.00000E+00 0.28213E+03 0.10318E+00 C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00 C -1BUSA-2BUSB-2 0.75387E-02 0.12835E-02 2 2 2 2 4 C 0.52771188E+00 0.55766835E+02 0.29991264E-04 0.31693770E-02 0.50000000E+02 C 0.00000E+00 0.43289E+05 0.97097E+00 0.00000E+00 0.77845E+03 0.29034E-01 C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00 C -1BUSA-3BUSB-3 0.30274E-02 0.12573E-02 3 3 2 2 4 C 0.13205030E+00 0.13401800E+03 0.12102672E-05 0.12283015E-02 0.50000000E+02 C 0.00000E+00 0.15517E+06 0.81796E+00 0.00000E+00 0.62830E+04 0.18204E+00 C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00 C -1BUSA-4BUSB-4 0.27802E-02 0.12569E-02 4 4 2 2 4 C 0.13237081E+00 0.14586679E+03 0.10231724E-05 0.11274909E-02 0.50000000E+02 C 0.00000E+00 0.16860E+06 0.80035E+00 0.00000E+00 0.68259E+04 0.19965E+00 C 0.00000E+00 0.10000E+01 0.00000E+00 0.00000E+00 0.10000E+01 0.00000E+00 C 0.87120E+00 0.00000E+00-0.68291E+00 0.00000E+00 0.10000E+01 0.00000E+00 C -0.41750E+00 0.00000E+00 C 0.88389E+00 0.00000E+00 0.55491E+00 0.00000E+00 0.40829E+00 0.00000E+00 C 0.10000E+01 0.00000E+00 C 0.10000E+01 0.00000E+00-0.95444E+00 0.00000E+00-0.36612E+00 0.00000E+00 C 0.81230E-01 0.00000E+00 C 0.99538E+00 0.00000E+00 0.10000E+01 0.00000E+00-0.14418E+00 0.00000E+00 C -0.28779E+00 0.00000E+00 C 0.13754E+00 0.00000E+00-0.13506E+00 0.00000E+00 0.66301E+00 0.00000E+00 C -0.32285E+00 0.00000E+00 C 0.13718E+00 0.00000E+00 0.10517E+00 0.00000E+00 0.25843E+00 0.00000E+00 C 0.72350E+00 0.00000E+00 C 0.38034E+00 0.00000E+00-0.42191E+00 0.00000E+00-0.56809E+00 0.00000E+00 C 0.13687E+00 0.00000E+00 C 0.38061E+00 0.00000E+00 0.44851E+00 0.00000E+00-0.23947E+00 0.00000E+00 C -0.49432E+00 0.00000E+00 C &&&&&&&&&&&&&&&&& END LUNIT7 CARDS PUNCHED BY DC-63 &&&&&&&& C Preceding branch cards exist as non-comment data until 27 November 2000 C when they are being replaced by more modern $INCLUDE use that makes C reference to cards punched by preceding DC-60: $INCLUDE, dc60a.pch, ! { Exclamation point to hold lower case is tolerated C In fact, it does nothing beginning 28 January 2001 C At the same time, output of SEMLYEN SETUP is changing so [Tv] and [Ti] C use wide rather than preceding narrow format. But that newer data is C documented by output of DC-60, so need not be documented here. TOWER 2. BUSB-1 2. .03 BUSB-2 2. .03 BLANK card ends all branch cards BUSB-3TOWER .000995 1. 3 BLANK cards ends all switch cards (here, just one, representing the fault) 14SA-3 533000. 50. 0.0 -1. 14SA-4 533000. 50. 180. -1. BLANK card ends source cards C Total network loss P-loss by summing injections = 1.227475331932E+07 C 1st inject: SA-3 533000. 533000. 22.124947951506 1512.2473010922 C 1st inject: 0.0 0.0 1512.0854428037 89.1617037 C Last inject: SA-4 -533000. 533000. -23.93416394087 1518.1059386521 C Last inject: .6527332453E-10 180.00000 -1517.917256232 -90.9033516 C C Step Time BUSB-3 FIL2 TOWER FIL4 FIL3 C TOWER C C BUSB-1 BUSA-2 BUSA-1 BUSA-4 BUSA-3 C C 0 0.0 .101427E7 0.0 0.0 630.561229 3942.45992 C -4.6091835 1.25763103 -3.3035273 -928794.53 927274.067 C 1 .1E-4 .1014316E7 0.0 0.0 630.452909 3941.48093 C -5.7370041 5.05435474 -4.8499099 -928814.11 927285.865 1 C Last step begins: 2000 .02 0.0 0.0 -4129.0322 3721.27842 -19338.153 C Last step begins: 1060.61608 -481.80296 -509.22959 -915751.91 163602.568 C Variable maxima : .1014355E7 0.0 5946.09635 40005.6129 123962.984 C Variable maxima : 9268.51692 4258.29012 14305.2037 .1049562E7 927287.754 C Times of maxima : .4E-4 0.0 .00723 .00952 .00505 C Times of maxima : .00102 .00227 .00227 .01071 .2E-4 PRINTER PLOT 2One section of 375 km. 144 .6 0.0 7.0 BUSA-2 { Plot limits: (-0.647, 2.660) BLANK card ending all plot cards BEGIN NEW DATA CASE C 2nd of two subcases is the same as the preceding subcase except for one C change: the addition of "Derive [Ti] from [Tv]" immediately following C the Semlyen branch cards. The answers change a little. Even the limits C on the PRINTER PLOT are different. Date of addition: 11 December 2000. PRINTED NUMBER WIDTH, 12, 2, { Request maximum precision (for 9 output columns) POWER FREQUENCY, 50., PEAK VOLTAGE MONITOR .000010 .020 50. 50. 1 5 1 1 1 -1 5 5 20 20 100 100 1000 1000 SA-3 BUSA-3 .1260.75 SA-4 BUSA-4 .1260.75 BUSA-1 2. .03 BUSA-2 2. .03 BUSA-3 FIL1 .1 47.12 FIL1 .1 90.76 FIL1 3. 74.24 FIL1 6.166.94 94.25 FIL1 12.314.16 11.06 FIL1 12.314.16 5.87 FIL2 .01 1021. FIL2 .1 14.14 BUSA-4 FIL3 .1 47.12 FIL3 FIL4 .1 90.76 FIL3 FIL4 3. 74.24 FIL3 FIL4 6.166.94 94.25 FIL3 FIL4 12.314.16 11.06 FIL3 FIL4 12.314.16 5.87 FIL4 .01 1021. FIL4 .01 14.14 $INCLUDE, dc60a.pch, { This is normal use, without any "!" (see subcase 2) Derive [Ti] from [Tv] TOWER 2. BUSB-1 2. .03 BUSB-2 2. .03 BLANK card ends all branch cards BUSB-3TOWER .000995 1. 3 BLANK cards ends all switch cards (here, just one, representing the fault) 14SA-3 533000. 50. 0.0 -1. 14SA-4 533000. 50. 180. -1. BLANK card ends source cards C First 16 output variables are electric-network voltage differences (upper voltage minus lower voltage); C Next 1 output variables are branch currents (flowing from the upper node to the lower node); C Step Time BUSB-3 FIL2 TOWER FIL4 FIL3 FIL1 BUSB-3 BUSB-4 BUSB-2 C TOWER C C BUSB-1 BUSA-2 BUSA-1 BUSA-4 BUSA-3 SA-3 SA-4 BUSB-3 C TOWER C 0 0.0 .1009903E7 0.0 0.0 625.729384 3912.27257 -3290.8384 .1009903E7 -.100856E7 4.71090545 C -4.7315816 1.50363292 -3.019058 -921677.25 923494.094 533000. -533000. 0.0 C 1 .1E-4 .1009922E7 0.0 0.0 625.744428 3912.80237 -3291.3514 .1009922E7 -.100858E7 4.60636774 C -4.6168248 2.20907585 -3.8531833 -921692.03 923507.81 532997.37 -532997.37 0.0 C 2 .2E-4 .1009931E7 0.0 0.0 625.757165 3913.34087 -3291.8771 .1009931E7 -.100859E7 4.53586824 C -4.5389958 2.951526 -4.73104 -921697.57 923512.279 532989.479 -532989.48 0.0 1 C 2000 .02 0.0 0.0 -4082.6074 3506.39056 -19843.969 33487.4084 -4082.6074 -994315.82 667.210123 C 1019.1604 -477.59394 -495.04968 -910823.4 166982.83 533000. -533000. -2041.3037 C C Overall simulation peak node voltage = 1.27438708E+06 occurred at bus "BUSB-4" at time [sec] = 9.42000000E-03 C Extrema of output variables follow. Order and column positioning are the same as for the preceding time-step loop output. C Variable maxima : .1009931E7 0.0 5887.54564 39979.7091 122521.51 252007.816 .1009931E7 .1274387E7 5514.37962 C 8875.03104 4249.33 13984.8846 .1041678E7 923512.279 533000. 533000. 2943.77282 C Times of maxima : .2E-4 0.0 .00723 .00952 .00505 .00848 .2E-4 .00942 .00102 C .00102 .00227 .00227 .01071 .2E-4 0.0 .01 .00723 C Variable minima : 0.0 0.0 -7105.8822 -35654.766 -134500.78 -375615.01 -7105.8822 -.113035E7 -7267.3484 C -11822.652 -1785.594 -1816.5115 -921697.57 -997977.99 -533000. -533000. -3552.9411 C Times of minima : .00101 0.0 .01463 .01069 .00608 .00575 .01463 .00101 .00101 C .00101 .01494 .0147 .2E-4 .0087 .01 0.0 .01463 PRINTER PLOT 2One section of 375 km. 144 .6 0.0 7.0 BUSA-2 { Plot limits: (-0.650, 2.600) BLANK card ending all plot cards BEGIN NEW DATA CASE BLANK